การแก้ปัญหาเมื่อเปิดคอมพิวเตอร์ แล้วมีข้อความขึ้นมาค้างอยู่ว่า

Verifying DMI Pool Data . . . . . ( . จุดกระพริบ ๆ )

ผมลองเสิร์ชการแก้ปัญหาจากเวปต่างๆดู บางคนบอกให้ลองเข้า Safe Mode (F8) ดูก่อน....ผมว่ามันไม่ได้หรอก เพราะปัญหามันเกิดก่อน ก่อนที่จะบูตเข้าวินโดวส์ (อันนี้ ของผมเป็น WindowsXP Pro SP3) ซะอีก...ไม่น่าจะเข้าเซฟโหมดได้นะ

เจอการแก้ปัญหาจากเวปนึง (ตามเครดิตด้านล่าง )เค้าว่าไว้ตามที่ก๊อปปี้ไว้ ด้านล่างนี้ ทำตามทีละข้อไปเลย 1-2-3.....10

 

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Computer Hangs at  " Verifying DMI Pool Data "

Q. During bootup my computer hangs at "Verifying DMI pool data." What is it and how do I fix it?

A. DMI or DesktopManagement Interface (pdf) is a layer of abstraction between system components and the software that manages them. The System Management BIOS (SMBIOS) is an extension of the Basic Input Output System (BIOS) that formulates and delivers this information to the operating system. The pool data is the information. In short, when the BIOS is "Verifying DMI pool data" it is verifying the table of data it sends to the operating system (Windows, etc.). If it isn't sucessful, it should return an error. Wait a reasonable period of time for it to finish. It may make take some time or it may be stuck. Possible fixes:

1. If you changed the hardware just before this problem occurred (e.g., installed a new hard disk drive), unchange it.

2. If you installed a new hard disk drive, set the motherboard CMOS Setup to Auto for the drive type. You may have to disconnect the drive first.

3. Enable "Reset Configuration Data" (may be "Force Update ESCD" in some CMOS Setuups) in the motherboard CMOS Setup PNP/PCI configuration. (Rebooting will automatically disabled it after it has done its thing.)

4. The CMOS may be corrupted. Clear it.

5. Disconnect all drives not required to boot the computer. If this fixes it, reconnect one at time.

6. The floppy drive may be bad or not connected properly.

7. Reseat all expansion boards.

8. Pull all boards not required to boot the computer.

9. Check your order of boot devices. Simple mistake, I know. But some motherboards will hang instead of moving on to the next boot device. My thanks to Adam Spade who contributed this step.

10. Charles Reaves writes: I had a hangup on the "Verifying DMI Pool data" step in the boot sequence. I researched several sites, including yours and have one thing to add to what was on your site. I had inadvertently left a USB memory stick reader (With stick installed) connected to a USB port. That was causing the error. I unplugged the memory stick and the machine booted fine. Anyone receiving this error should be sure that they do not have a reader, camera, etc., connected to the computer.

Please see our Contact page if you have any comments or corrections that would make this article better. Please use our Forums if you need help with a computer or network problem.

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

ควรจะอ่านก่อนนะ ว่า DMI คืออะไร แล้วก็ทำตามไปเรื่อย ๆ ......สำหรับผมทำสำเร็จ...แปลมั่ว ๆ เอา 555+

 

เครดิต ==>> http://www.duxcw.com <<== 

 

 

Comment

Comment:

Tweet